Your hvac installation specialists in Danville, CA. Free assessments, certified technicians, and guaranteed results.
A complete HVAC installation from KIC Refrigeration in Danville, CA addresses every element in the comfort chain, from the air handler and condensing unit to the thermostat, ductwork, and filtration system. We ensure proper airflow balance, verified refrigerant charge, tested safety controls, and code-compliant operation before turning the system over to you.
Danville homeowners and businesses count on reliable hvac installation to maintain comfort and protect indoor air quality. Serving a town of 43,333 across California, KIC Refrigeration brings the experience and crew depth to handle hvac installation projects of any scale. We begin every job with an honest evaluation and a clear, written estimate.
Our hvac installation technicians in Danville, CA are NATE-certified, EPA 608 licensed, and equipped with advanced diagnostic tools. From the initial inspection through final commissioning, we maintain open communication and hold ourselves to the highest standards. That is how KIC Refrigeration has earned the trust of homeowners across California.
A clear, step-by-step approach to every hvac installation project we take on.
We survey your property, assess your existing HVAC infrastructure, and perform a Manual J load calculation to determine the correct system size. We evaluate ductwork condition, electrical capacity, and equipment location options.
Our Danville team presents two to three system options matched to your load calculation. We compare SEER2 and AFUE ratings, explain the differences between single-stage, two-stage, and variable-speed equipment, and factor in available manufacturer rebates, utility incentives, and federal tax credits for Danville homeowners.
KIC Refrigeration installs HVAC systems in Danville, CA to the highest standards. We set equipment on level, vibration-isolated mounting, braze all refrigerant connections with nitrogen flowing, pressure test with dry nitrogen, evacuate to below 500 microns, charge by weight, seal all duct connections with mastic, and verify gas piping sizing and connections.
We start the new system, verify operation in all modes, measure airflow, check refrigerant charge, program the thermostat, register the warranty, and provide you with all documentation including equipment manuals, warranty cards, and commissioning readings.
Common questions about hvac installation costs, timelines, and what to expect.
Complete HVAC installation in Danville ranges from $7,000 to $15,000 for a mid-efficiency furnace and AC combination — typically an 80 percent AFUE furnace paired with a 14.3 to 16 SEER2 condenser. High-efficiency systems with variable-speed blowers and two-stage or variable-speed compressors run $12,000 to $22,000 but deliver significantly lower operating costs and qualify for federal tax credits. Heat pump systems fall between $5,000 and $18,000 depending on whether the system is single-stage, variable-speed, or a dual-fuel configuration. Ductwork modifications or new duct runs add $1,000 to $5,000. KIC Refrigeration provides detailed written proposals for Danville homeowners with every cost itemized and no hidden fees.
Correct HVAC system sizing is determined by a Manual J residential load calculation — the ACCA industry standard — that accounts for your home square footage, ceiling height, insulation R-values, window area and U-factor, air infiltration rate, duct losses, occupancy, and the local CA winter and summer design temperatures. As a rough reference, a well-insulated 2,000-square-foot home in Danville typically needs a 2.5 to 3.5 ton system, while a poorly insulated home of the same size may need 4 tons. KIC Refrigeration never estimates by rule of thumb — we run a proper calculation for your specific Danville home to avoid oversizing, which causes short cycling, high humidity, and premature compressor wear.
A standard furnace and AC replacement in Danville takes 1 to 2 days when existing ductwork, gas piping, and electrical service are adequate and the new equipment fits in the same location. A complete system replacement that includes ductwork modifications, new trunk lines, equipment relocation from basement to attic or vice versa, electrical panel upgrades, or zoning system installation may take 3 to 5 days. Multi-zone mini-split installations with 3 to 5 indoor heads typically take 2 to 3 days. KIC Refrigeration provides a clear timeline in every proposal, coordinates scheduling around your Danville home availability, and keeps you informed on progress every step of the way.
Yes. KIC Refrigeration pulls all required mechanical, electrical, and gas permits for every HVAC installation in Danville, CA. We prepare the permit application with equipment specifications and installation plans, pay the permit fee, schedule the inspection with the local building department, meet the inspector on-site, and ensure the installation passes all applicable mechanical code requirements. A building permit is not optional — it is required by law in most Danville jurisdictions, and an unpermitted installation can void the manufacturer equipment warranty, create title problems when selling the home, and may not be covered by homeowner insurance if an HVAC failure causes property damage. KIC Refrigeration includes permitting in every installation project.
Real feedback from customers across the country about the quality of our work.
"AC tune-up before summer. Technician was early, finished in about forty-five minutes, and gave me a clean bill of health on the system. Easy process."
"KIC Refrigeration has serviced our commercial HVAC system for two years now. Always professional, always on time. Would not trust anyone else."
"Emergency HVAC repair at midnight with a newborn in the house. They treated it like the emergency it was and had our heat back on in under two hours."